Engineering report · reviewed against NEC 2026 & BS 7671:2018+A2
Engineering Breakdown: Running a 3/4 HP Submersible Sewage Ejector Pump on the Anker SOLIX C1000
When pairing the Anker SOLIX C1000 (1,056 Wh LiFePO4 capacity, 1,800 W continuous, 2,400 W surge) with a 3/4 HP Submersible Sewage Ejector Pump (1,150 W running, 2,900 W starting surge), the system operates at 64% of continuous inverter capacity on a 120 V North American circuit and 64% on a 230 V UK/EU/AU circuit. Our North American verdict is Surge Overload, so the runtime figures below are theoretical battery-energy values only. Wiring the connection over a 25 ft run calls for a 15 A breaker and 14 AWG copper, terminated at a NEMA 5-15P / 5-20P connection.
1. Compatibility Verdict & Inverter Load Utilization
In North American mode the 3/4 HP Submersible Sewage Ejector Pump loads the Anker SOLIX C1000's inverter to 64% of its 1,800 W continuous rating and 121% of its 2,400 W surge rating. Running watts fit, but the start-up surge exceeds what the inverter can deliver even momentarily, so expect an overload trip each time the motor starts. A soft-start device or stepping up to the Jackery Explorer 1000 v2 resolves it.
| Check | Load requires | Anker SOLIX C1000 provides | US/NA | UK/EU/AU |
|---|---|---|---|---|
| Continuous output | 1,150 W | 1,800 W | Pass | Pass |
| Start-up surge | 2,900 W | 2,400 W | Fail | Fail |
| Voltage | 120 V / 230 V | 120 V / 230 V | Pass | Pass |
| Connection | NEMA 5-15P / 5-20P | NEMA 5-20R | UK/EU/AU: BS 1363 13A / Schuko CEE 7/4 / AS/NZS 3112 10A | |
Pumps are short-cycling, high-inrush loads. A well or sump pump might run for only 1–3 minutes at a time, but every start pulls 2,900 W — 2.5× its 1,150 W running draw — as the motor accelerates a column of water. That is why a pump that "only uses 1,150 W" still trips undersized inverters. This is a 120 V pump, so it plugs straight into a standard household receptacle on the power station. A larger pressure tank reduces the number of starts per hour and is a worthwhile upgrade for off-grid systems built around the Anker SOLIX C1000.
As a portable power station, the Anker SOLIX C1000 integrates the LiFePO4 battery, inverter, MPPT solar controller and AC outlets in one chassis, so it can be wheeled to the load or connected to a transfer switch through its NEMA 5-20R outlet.
Compatible alternative: the Jackery Explorer 1000 v2 with the 3/4 HP Submersible Sewage Ejector Pump report shows the full sizing for a unit that passes all three checks.
2. Real-World Runtime by Duty Cycle
Nameplate capacity is not usable capacity. DC-to-AC conversion, battery management overhead and cell protection reduce the 1,056 Wh rating to about 898 Wh of deliverable AC energy (85% system efficiency). Duty cycle is the share of each hour the load actually draws its running power — thermostats, pressure switches and intermittent use all lower it.
| Duty cycle | Average draw | Runtime (no solar) | Energy per 24 h |
|---|---|---|---|
| 25% | 288 W | 3.1 hrs | 6.9 kWh |
| 50% | 575 W | 1.6 hrs | 13.8 kWh |
| 65% | 748 W | 1.2 hrs | 17.9 kWh |
| 100% | 1,150 W | 47 min | 27.6 kWh |
Even at a 50% duty cycle the battery lasts 1.6 hrs, so plan on solar, grid or generator recharging for anything longer than an evening outage. Because the inverter cannot actually run this load in North American mode, treat these numbers as an energy-budget reference for a compatible inverter of the same capacity.
3. NEC 125% Breaker & Copper Wire Gauge Sizing
NEC 210.19(A) and 210.20(A) require conductors and overcurrent devices for continuous loads — anything running three hours or more, which includes EV charging and HVAC — to be rated at 125% of the load current. For this pairing: 1,150 W ÷ 120 V = 9.6 A, × 1.25 = 12.0 A, which rounds up to the next standard NEC 240.6 size of 15 A. The conductor must be protected by that breaker (75 °C ampacity at least 15 A) and keep round-trip voltage drop at or below 3%, so longer runs are upsized.
Voltage drop % = (2 × L × I × R) ÷ V × 100
North America (NEC, THHN copper, 75 °C)
| One-way distance | Breaker | Min. copper | Voltage drop | Note |
|---|---|---|---|---|
| 25 ft (7.6 m) | 15 A | 14 AWG | 1.23% | Sized by ampacity |
| 50 ft (15.2 m) | 15 A | 14 AWG | 2.45% | Sized by ampacity |
| 75 ft (22.9 m) | 15 A | 12 AWG | 2.31% | Upsized for voltage drop |
| 100 ft (30.5 m) | 15 A | 10 AWG | 1.93% | Upsized for voltage drop |
UK / EU / Australia (IEC 60364 / BS 7671, PVC copper, method C)
IEC-based codes size protection by design current rather than a blanket 125% multiplier: Ib ≤ In ≤ Iz. At 230 V the load draws 5.0 A, so a 6 A Type B/C MCB with RCD protection applies. In the UK, BS 7671 Section 722 additionally requires a dedicated circuit and Type A or Type B RCD for EV charge points.
| One-way distance | MCB | Min. cable | Voltage drop |
|---|---|---|---|
| 7.5 m (25 ft) | 6 A | 1.5 mm² | 0.39% |
| 15 m (49 ft) | 6 A | 1.5 mm² | 0.79% |
| 22.5 m (74 ft) | 6 A | 1.5 mm² | 1.18% |
| 30 m (98 ft) | 6 A | 1.5 mm² | 1.58% |
Moving the Anker SOLIX C1000 from 25 ft to 100 ft away forces the conductor up from 14 AWG to 10 AWG — park the unit as close to the load as ventilation and weather protection allow.
4. Solar Array Recharge Time Breakdown
The Anker SOLIX C1000 accepts up to 600 W of photovoltaic input. Real arrays rarely deliver nameplate output, so we apply an 80% harvest factor for MPPT conversion, cell temperature and soiling, and convert hours to days using 4.5 peak-sun-hours — a conservative annual average for the US, southern Europe and Australia (UK winters can fall below 1.5).
| PV array | Real harvest | 0–100% recharge | Sun-days @ 4.5 PSH | Net with load @ 50% |
|---|---|---|---|---|
| 400 W | 320 W | 3.3 hrs | 0.7 | −255 W |
| 600 W | 480 W | 2.2 hrs | 0.5 | −95 W |
A typical 600 W portable array refills the battery in about 2.2 hrs of strong sun, while maxing out the 600 W input cuts that to 2.2 hrs. To fully offset the 3/4 HP Submersible Sewage Ejector Pump at a 50% duty cycle (575 W average) during daylight you need roughly 750 W of panels, which exceeds this unit's 600 W input limit — solar can slow the drain but not eliminate it.
5. Frequently Asked Questions
Can the Anker SOLIX C1000 run a 3/4 HP Submersible Sewage Ejector Pump?
Not reliably in North America — our verdict is "Surge Overload". The 2,900 W start-up surge exceeds the 2,400 W surge rating. The Jackery Explorer 1000 v2 is a compatible alternative. In UK/EU/AU 230 V mode the verdict is "Surge Overload".
How long will the Anker SOLIX C1000 run a 3/4 HP Submersible Sewage Ejector Pump?
With 1,056 Wh of capacity and 85% inverter efficiency, expect about 47 min of continuous operation and 1.6 hrs at a 50% duty cycle — theoretical figures, since the inverter cannot actually sustain this load. Adding solar input during the day extends this further.
What breaker and wire size do I need to connect a 3/4 HP Submersible Sewage Ejector Pump to the Anker SOLIX C1000?
In the US, 1,150 W at 120 V is 9.6 A; applying the NEC 125% continuous-load rule gives 12.0 A, so use a 15 A breaker and 14 AWG copper for runs up to 25 ft (1.2% voltage drop). In 230 V markets the load draws 5.0 A, protected by a 6 A MCB on 1.5 mm² cable for runs up to 7.5 m. Receptacle: NEMA 5-15P / 5-20P (US) or BS 1363 13A / Schuko CEE 7/4 / AS/NZS 3112 10A (UK/EU/AU).
How long does it take to recharge the Anker SOLIX C1000 with solar panels?
With an 600 W array and an 80% real-world harvest factor, a full recharge takes about 2.2 hrs of peak sun (0.5 days at 4.5 peak-sun-hours). At its maximum 600 W solar input it drops to 2.2 hrs.
Methodology & safety note
Specifications come from manufacturer datasheets in our open dataset; ampacity and resistance values follow NEC Table 310.16 and Chapter 9 Table 8, and BS 7671 Appendix 4. Calculations assume copper conductors, 30 °C ambient and no bundling derating. Inverter-to-panel connections require a listed transfer switch or interlock to prevent back-feeding the grid. These results are an engineering estimate, not a substitute for a licensed electrician and local permit. See our methodology and safety disclaimer.