Engineering report · reviewed against NEC 2026 & BS 7671:2018+A2
Engineering Breakdown: Running a 10-Inch Jobsite Table Saw (15A Universal Motor) on the Anker SOLIX F2000 (PowerHouse 767)
When pairing the Anker SOLIX F2000 (PowerHouse 767) (2,048 Wh LiFePO4 capacity, 2,400 W continuous, 3,600 W surge) with a 10-Inch Jobsite Table Saw (15A Universal Motor) (1,800 W running, 3,900 W starting surge), the system operates at 75% of continuous inverter capacity on a 120 V North American circuit and 75% on a 230 V UK/EU/AU circuit. Our North American verdict is Surge Overload, so the runtime figures below are theoretical battery-energy values only. Wiring the connection over a 25 ft run calls for a 20 A breaker and 12 AWG copper, terminated at a NEMA 5-15P / 5-20P connection.
1. Compatibility Verdict & Inverter Load Utilization
In North American mode the 10-Inch Jobsite Table Saw (15A Universal Motor) loads the Anker SOLIX F2000 (PowerHouse 767)'s inverter to 75% of its 2,400 W continuous rating and 108% of its 3,600 W surge rating. Running watts fit, but the start-up surge exceeds what the inverter can deliver even momentarily, so expect an overload trip each time the motor starts. A soft-start device or stepping up to the EcoFlow Delta 2 Max resolves it.
| Check | Load requires | Anker SOLIX F2000 provides | US/NA | UK/EU/AU |
|---|---|---|---|---|
| Continuous output | 1,800 W | 2,400 W | Pass | Pass |
| Start-up surge | 3,900 W | 3,600 W | Fail | Fail |
| Voltage | 120 V / 230 V | 120 V / 230 V | Pass | Pass |
| Connection | NEMA 5-15P / 5-20P | NEMA TT-30R / 5-20R | UK/EU/AU: BS 1363 13A / Schuko CEE 7/4 / AS/NZS 3112 10A | |
Workshop tools combine high running watts with brutal start-up spikes: universal motors and induction motors reach 2.2× their running draw (3,900 W) when the blade, drum or compressor head spins up under load. Because tool use is intermittent — measured in minutes per hour rather than hours per day — battery capacity is rarely the limit, but inverter surge capacity is. At 3,600 W of surge, the Anker SOLIX F2000 (PowerHouse 767) will likely shut down the moment the motor starts. Avoid long, thin extension cords on job sites; voltage sag at the tool increases current and heat.
As a portable power station, the Anker SOLIX F2000 (PowerHouse 767) integrates the LiFePO4 battery, inverter, MPPT solar controller and AC outlets in one chassis, so it can be wheeled to the load or connected to a transfer switch through its NEMA TT-30R / 5-20R outlet.
Compatible alternative: the EcoFlow Delta 2 Max with the 10-Inch Jobsite Table Saw (15A Universal Motor) report shows the full sizing for a unit that passes all three checks.
2. Real-World Runtime by Duty Cycle
Nameplate capacity is not usable capacity. DC-to-AC conversion, battery management overhead and cell protection reduce the 2,048 Wh rating to about 1,741 Wh of deliverable AC energy (85% system efficiency). Duty cycle is the share of each hour the load actually draws its running power — thermostats, pressure switches and intermittent use all lower it.
| Duty cycle | Average draw | Runtime (no solar) | Energy per 24 h |
|---|---|---|---|
| 25% | 450 W | 3.9 hrs | 10.8 kWh |
| 50% | 900 W | 1.9 hrs | 21.6 kWh |
| 65% | 1,170 W | 1.5 hrs | 28.1 kWh |
| 100% | 1,800 W | 58 min | 43.2 kWh |
Even at a 50% duty cycle the battery lasts 1.9 hrs, so plan on solar, grid or generator recharging for anything longer than an evening outage. Because the inverter cannot actually run this load in North American mode, treat these numbers as an energy-budget reference for a compatible inverter of the same capacity.
3. NEC 125% Breaker & Copper Wire Gauge Sizing
NEC 210.19(A) and 210.20(A) require conductors and overcurrent devices for continuous loads — anything running three hours or more, which includes EV charging and HVAC — to be rated at 125% of the load current. For this pairing: 1,800 W ÷ 120 V = 15.0 A, × 1.25 = 18.8 A, which rounds up to the next standard NEC 240.6 size of 20 A. The conductor must be protected by that breaker (75 °C ampacity at least 20 A) and keep round-trip voltage drop at or below 3%, so longer runs are upsized.
Voltage drop % = (2 × L × I × R) ÷ V × 100
North America (NEC, THHN copper, 75 °C)
| One-way distance | Breaker | Min. copper | Voltage drop | Note |
|---|---|---|---|---|
| 25 ft (7.6 m) | 20 A | 12 AWG | 1.21% | Sized by ampacity |
| 50 ft (15.2 m) | 20 A | 12 AWG | 2.41% | Sized by ampacity |
| 75 ft (22.9 m) | 20 A | 10 AWG | 2.27% | Upsized for voltage drop |
| 100 ft (30.5 m) | 20 A | 8 AWG | 1.91% | Upsized for voltage drop |
UK / EU / Australia (IEC 60364 / BS 7671, PVC copper, method C)
IEC-based codes size protection by design current rather than a blanket 125% multiplier: Ib ≤ In ≤ Iz. At 230 V the load draws 7.8 A, so a 10 A Type B/C MCB with RCD protection applies. In the UK, BS 7671 Section 722 additionally requires a dedicated circuit and Type A or Type B RCD for EV charge points.
| One-way distance | MCB | Min. cable | Voltage drop |
|---|---|---|---|
| 7.5 m (25 ft) | 10 A | 1.5 mm² | 0.62% |
| 15 m (49 ft) | 10 A | 1.5 mm² | 1.24% |
| 22.5 m (74 ft) | 10 A | 1.5 mm² | 1.85% |
| 30 m (98 ft) | 10 A | 1.5 mm² | 2.47% |
Moving the Anker SOLIX F2000 (PowerHouse 767) from 25 ft to 100 ft away forces the conductor up from 12 AWG to 8 AWG — park the unit as close to the load as ventilation and weather protection allow.
4. Solar Array Recharge Time Breakdown
The Anker SOLIX F2000 (PowerHouse 767) accepts up to 1,000 W of photovoltaic input. Real arrays rarely deliver nameplate output, so we apply an 80% harvest factor for MPPT conversion, cell temperature and soiling, and convert hours to days using 4.5 peak-sun-hours — a conservative annual average for the US, southern Europe and Australia (UK winters can fall below 1.5).
| PV array | Real harvest | 0–100% recharge | Sun-days @ 4.5 PSH | Net with load @ 50% |
|---|---|---|---|---|
| 400 W | 320 W | 6.4 hrs | 1.4 | −580 W |
| 800 W | 640 W | 3.2 hrs | 0.7 | −260 W |
| 1,000 W | 800 W | 2.6 hrs | 0.6 | −100 W |
A typical 800 W portable array refills the battery in about 3.2 hrs of strong sun, while maxing out the 1,000 W input cuts that to 2.6 hrs. To fully offset the 10-Inch Jobsite Table Saw (15A Universal Motor) at a 50% duty cycle (900 W average) during daylight you need roughly 1,150 W of panels, which exceeds this unit's 1,000 W input limit — solar can slow the drain but not eliminate it.
5. Frequently Asked Questions
Can the Anker SOLIX F2000 (PowerHouse 767) run a 10-Inch Jobsite Table Saw (15A Universal Motor)?
Not reliably in North America — our verdict is "Surge Overload". The 3,900 W start-up surge exceeds the 3,600 W surge rating. The EcoFlow Delta 2 Max is a compatible alternative. In UK/EU/AU 230 V mode the verdict is "Surge Overload".
How long will the Anker SOLIX F2000 (PowerHouse 767) run a 10-Inch Jobsite Table Saw (15A Universal Motor)?
With 2,048 Wh of capacity and 85% inverter efficiency, expect about 58 min of continuous operation and 1.9 hrs at a 50% duty cycle — theoretical figures, since the inverter cannot actually sustain this load. Adding solar input during the day extends this further.
What breaker and wire size do I need to connect a 10-Inch Jobsite Table Saw (15A Universal Motor) to the Anker SOLIX F2000 (PowerHouse 767)?
In the US, 1,800 W at 120 V is 15.0 A; applying the NEC 125% continuous-load rule gives 18.8 A, so use a 20 A breaker and 12 AWG copper for runs up to 25 ft (1.2% voltage drop). In 230 V markets the load draws 7.8 A, protected by a 10 A MCB on 1.5 mm² cable for runs up to 7.5 m. Receptacle: NEMA 5-15P / 5-20P (US) or BS 1363 13A / Schuko CEE 7/4 / AS/NZS 3112 10A (UK/EU/AU).
How long does it take to recharge the Anker SOLIX F2000 (PowerHouse 767) with solar panels?
With an 800 W array and an 80% real-world harvest factor, a full recharge takes about 3.2 hrs of peak sun (0.7 days at 4.5 peak-sun-hours). At its maximum 1,000 W solar input it drops to 2.6 hrs.
Methodology & safety note
Specifications come from manufacturer datasheets in our open dataset; ampacity and resistance values follow NEC Table 310.16 and Chapter 9 Table 8, and BS 7671 Appendix 4. Calculations assume copper conductors, 30 °C ambient and no bundling derating. Inverter-to-panel connections require a listed transfer switch or interlock to prevent back-feeding the grid. These results are an engineering estimate, not a substitute for a licensed electrician and local permit. See our methodology and safety disclaimer.