Engineering report · reviewed against NEC 2026 & BS 7671:2018+A2
Engineering Breakdown: Running a 3/4 HP Submersible Sewage Ejector Pump on the EcoFlow Delta 2 Max
When pairing the EcoFlow Delta 2 Max (2,048 Wh LiFePO4 capacity, 2,400 W continuous, 4,800 W surge) with a 3/4 HP Submersible Sewage Ejector Pump (1,150 W running, 2,900 W starting surge), the system operates at 48% of continuous inverter capacity on a 120 V North American circuit and 48% on a 230 V UK/EU/AU circuit. At a 100% duty cycle and 85% inverter efficiency, a full battery delivers roughly 1.5 hrs of off-grid runtime. Wiring the connection over a 25 ft run calls for a 15 A breaker and 14 AWG copper, terminated at a NEMA 5-15P / 5-20P connection.
1. Compatibility Verdict & Inverter Load Utilization
In North American mode the 3/4 HP Submersible Sewage Ejector Pump loads the EcoFlow Delta 2 Max's inverter to 48% of its 2,400 W continuous rating and 60% of its 4,800 W surge rating. Both figures are under the 80% sustained-load guideline, so this is a comfortable, verified match with 1,250 W of spare capacity for lights, a router or a refrigerator on the same unit.
| Check | Load requires | EcoFlow Delta 2 Max provides | US/NA | UK/EU/AU |
|---|---|---|---|---|
| Continuous output | 1,150 W | 2,400 W | Pass | Pass |
| Start-up surge | 2,900 W | 4,800 W | Pass | Pass |
| Voltage | 120 V / 230 V | 120 V / 230 V | Pass | Pass |
| Connection | NEMA 5-15P / 5-20P | NEMA 5-20R | UK/EU/AU: BS 1363 13A / Schuko CEE 7/4 / AS/NZS 3112 10A | |
Pumps are short-cycling, high-inrush loads. A well or sump pump might run for only 1–3 minutes at a time, but every start pulls 2,900 W — 2.5× its 1,150 W running draw — as the motor accelerates a column of water. That is why a pump that "only uses 1,150 W" still trips undersized inverters. This is a 120 V pump, so it plugs straight into a standard household receptacle on the power station. A larger pressure tank reduces the number of starts per hour and is a worthwhile upgrade for off-grid systems built around the EcoFlow Delta 2 Max.
As a portable power station, the EcoFlow Delta 2 Max integrates the LiFePO4 battery, inverter, MPPT solar controller and AC outlets in one chassis, so it can be wheeled to the load or connected to a transfer switch through its NEMA 5-20R outlet.
2. Real-World Runtime by Duty Cycle
Nameplate capacity is not usable capacity. DC-to-AC conversion, battery management overhead and cell protection reduce the 2,048 Wh rating to about 1,741 Wh of deliverable AC energy (85% system efficiency). Duty cycle is the share of each hour the load actually draws its running power — thermostats, pressure switches and intermittent use all lower it.
| Duty cycle | Average draw | Runtime (no solar) | Energy per 24 h |
|---|---|---|---|
| 25% | 288 W | 6.1 hrs | 6.9 kWh |
| 50% | 575 W | 3.0 hrs | 13.8 kWh |
| 65% | 748 W | 2.3 hrs | 17.9 kWh |
| 100% | 1,150 W | 1.5 hrs | 27.6 kWh |
Even at a 50% duty cycle the battery lasts 3.0 hrs, so plan on solar, grid or generator recharging for anything longer than an evening outage.
3. NEC 125% Breaker & Copper Wire Gauge Sizing
NEC 210.19(A) and 210.20(A) require conductors and overcurrent devices for continuous loads — anything running three hours or more, which includes EV charging and HVAC — to be rated at 125% of the load current. For this pairing: 1,150 W ÷ 120 V = 9.6 A, × 1.25 = 12.0 A, which rounds up to the next standard NEC 240.6 size of 15 A. The conductor must be protected by that breaker (75 °C ampacity at least 15 A) and keep round-trip voltage drop at or below 3%, so longer runs are upsized.
Voltage drop % = (2 × L × I × R) ÷ V × 100
North America (NEC, THHN copper, 75 °C)
| One-way distance | Breaker | Min. copper | Voltage drop | Note |
|---|---|---|---|---|
| 25 ft (7.6 m) | 15 A | 14 AWG | 1.23% | Sized by ampacity |
| 50 ft (15.2 m) | 15 A | 14 AWG | 2.45% | Sized by ampacity |
| 75 ft (22.9 m) | 15 A | 12 AWG | 2.31% | Upsized for voltage drop |
| 100 ft (30.5 m) | 15 A | 10 AWG | 1.93% | Upsized for voltage drop |
UK / EU / Australia (IEC 60364 / BS 7671, PVC copper, method C)
IEC-based codes size protection by design current rather than a blanket 125% multiplier: Ib ≤ In ≤ Iz. At 230 V the load draws 5.0 A, so a 6 A Type B/C MCB with RCD protection applies. In the UK, BS 7671 Section 722 additionally requires a dedicated circuit and Type A or Type B RCD for EV charge points.
| One-way distance | MCB | Min. cable | Voltage drop |
|---|---|---|---|
| 7.5 m (25 ft) | 6 A | 1.5 mm² | 0.39% |
| 15 m (49 ft) | 6 A | 1.5 mm² | 0.79% |
| 22.5 m (74 ft) | 6 A | 1.5 mm² | 1.18% |
| 30 m (98 ft) | 6 A | 1.5 mm² | 1.58% |
Moving the EcoFlow Delta 2 Max from 25 ft to 100 ft away forces the conductor up from 14 AWG to 10 AWG — park the unit as close to the load as ventilation and weather protection allow.
4. Solar Array Recharge Time Breakdown
The EcoFlow Delta 2 Max accepts up to 1,000 W of photovoltaic input. Real arrays rarely deliver nameplate output, so we apply an 80% harvest factor for MPPT conversion, cell temperature and soiling, and convert hours to days using 4.5 peak-sun-hours — a conservative annual average for the US, southern Europe and Australia (UK winters can fall below 1.5).
| PV array | Real harvest | 0–100% recharge | Sun-days @ 4.5 PSH | Net with load @ 50% |
|---|---|---|---|---|
| 400 W | 320 W | 6.4 hrs | 1.4 | −255 W |
| 800 W | 640 W | 3.2 hrs | 0.7 | +65 W |
| 1,000 W | 800 W | 2.6 hrs | 0.6 | +225 W |
A typical 800 W portable array refills the battery in about 3.2 hrs of strong sun, while maxing out the 1,000 W input cuts that to 2.6 hrs. To fully offset the 3/4 HP Submersible Sewage Ejector Pump at a 50% duty cycle (575 W average) during daylight you need roughly 750 W of panels, which this unit can accept.
5. Frequently Asked Questions
Can the EcoFlow Delta 2 Max run a 3/4 HP Submersible Sewage Ejector Pump?
Yes. The EcoFlow Delta 2 Max delivers 2,400 W continuous and 4,800 W surge, covering the 3/4 HP Submersible Sewage Ejector Pump's 1,150 W running and 2,900 W start-up draw at 48% inverter utilization.
How long will the EcoFlow Delta 2 Max run a 3/4 HP Submersible Sewage Ejector Pump?
With 2,048 Wh of capacity and 85% inverter efficiency, expect about 1.5 hrs of continuous operation and 3.0 hrs at a 50% duty cycle. Adding solar input during the day extends this further.
What breaker and wire size do I need to connect a 3/4 HP Submersible Sewage Ejector Pump to the EcoFlow Delta 2 Max?
In the US, 1,150 W at 120 V is 9.6 A; applying the NEC 125% continuous-load rule gives 12.0 A, so use a 15 A breaker and 14 AWG copper for runs up to 25 ft (1.2% voltage drop). In 230 V markets the load draws 5.0 A, protected by a 6 A MCB on 1.5 mm² cable for runs up to 7.5 m. Receptacle: NEMA 5-15P / 5-20P (US) or BS 1363 13A / Schuko CEE 7/4 / AS/NZS 3112 10A (UK/EU/AU).
How long does it take to recharge the EcoFlow Delta 2 Max with solar panels?
With an 800 W array and an 80% real-world harvest factor, a full recharge takes about 3.2 hrs of peak sun (0.7 days at 4.5 peak-sun-hours). At its maximum 1,000 W solar input it drops to 2.6 hrs.
Methodology & safety note
Specifications come from manufacturer datasheets in our open dataset; ampacity and resistance values follow NEC Table 310.16 and Chapter 9 Table 8, and BS 7671 Appendix 4. Calculations assume copper conductors, 30 °C ambient and no bundling derating. Inverter-to-panel connections require a listed transfer switch or interlock to prevent back-feeding the grid. These results are an engineering estimate, not a substitute for a licensed electrician and local permit. See our methodology and safety disclaimer.