Engineering report · reviewed against NEC 2026 & BS 7671:2018+A2
Engineering Breakdown: Running a 5 LPM Home Stationary Oxygen Concentrator on the Sungrow SH10RS Hybrid Inverter + Battery
When pairing the Sungrow SH10RS Hybrid Inverter + Battery (9,600 Wh LiFePO4 capacity, 10,000 W continuous, 15,000 W surge) with a 5 LPM Home Stationary Oxygen Concentrator (350 W running, 600 W starting surge), the system operates at 4% of continuous inverter capacity on a 230 V UK/EU/AU circuit. At a 100% duty cycle and 85% inverter efficiency, a full battery delivers roughly 23.3 hrs of off-grid runtime. Wiring the connection over a 7.5 m run calls for a 6 A MCB and 1.5 mm² copper, terminated at a BS 1363 13A / Schuko CEE 7/4 / AS/NZS 3112 10A connection.
1. Compatibility Verdict & Inverter Load Utilization
In UK/EU/AU 230 V mode the 5 LPM Home Stationary Oxygen Concentrator loads the Sungrow SH10RS Hybrid Inverter + Battery's inverter to 4% of its 10,000 W continuous rating and 4% of its 15,000 W surge rating. Both figures are under the 80% sustained-load guideline, so this is a comfortable, verified match with 9,650 W of spare capacity for lights, a router or a refrigerator on the same unit.
| Check | Load requires | Sungrow SH10RS Hybrid Inverter + Battery provides | UK/EU/AU |
|---|---|---|---|
| Continuous output | 350 W | 10,000 W | Pass |
| Start-up surge | 600 W | 15,000 W | Pass |
| Voltage | 230 V | 230 V | Pass |
| Connection | BS 1363 13A / Schuko CEE 7/4 / AS/NZS 3112 10A | Hardwired consumer unit (RCBO protected) |
Critical loads value uptime over raw power. At 350 W, this equipment is small relative to the Sungrow SH10RS Hybrid Inverter + Battery's 10,000 W inverter, so the deciding factors are runtime, pure-sine output quality and switchover time. Most modern power stations offer UPS or EPS pass-through with a 10–30 ms transfer, which is fast enough for CPAP machines, routers and servers with active-PFC power supplies. For medical devices, always confirm with the device manufacturer and keep a secondary backup plan; for CPAP specifically, a DC adapter can extend runtime by 20–30% by skipping inverter losses.
The Sungrow SH10RS Hybrid Inverter + Battery is a grid-tied hybrid inverter with battery storage, widely installed across Australia and New Zealand under AS/NZS 4777 and AS/NZS 3000. Backup to essential circuits requires a dedicated backup output and changeover arrangement.
2. Real-World Runtime by Duty Cycle
Nameplate capacity is not usable capacity. DC-to-AC conversion, battery management overhead and cell protection reduce the 9,600 Wh rating to about 8,160 Wh of deliverable AC energy (85% system efficiency). Duty cycle is the share of each hour the load actually draws its running power — thermostats, pressure switches and intermittent use all lower it.
| Duty cycle | Average draw | Runtime (no solar) | Energy per 24 h |
|---|---|---|---|
| 25% | 88 W | 3.9 days | 2.1 kWh |
| 50% | 175 W | 46.6 hrs | 4.2 kWh |
| 65% | 228 W | 35.9 hrs | 5.5 kWh |
| 100% | 350 W | 23.3 hrs | 8.4 kWh |
At a 50% duty cycle the Sungrow SH10RS Hybrid Inverter + Battery covers a full day (46.6 hrs) without any recharge — ample for a typical overnight outage.
3. BS 7671 / IEC 60364 Breaker & Cable Sizing
IEC-based codes size protection by design current rather than a blanket 125% multiplier: Ib ≤ In ≤ Iz. At 230 V the load draws 1.5 A, so a 6 A Type B/C MCB with RCD protection applies. In the UK, BS 7671 Section 722 additionally requires a dedicated circuit and Type A or Type B RCD for EV charge points.
| One-way distance | MCB | Min. cable | Voltage drop |
|---|---|---|---|
| 7.5 m (25 ft) | 6 A | 1.5 mm² | 0.12% |
| 15 m (49 ft) | 6 A | 1.5 mm² | 0.24% |
| 22.5 m (74 ft) | 6 A | 1.5 mm² | 0.36% |
| 30 m (98 ft) | 6 A | 1.5 mm² | 0.48% |
Because the current is modest, 1.5 mm² copper stays within the voltage-drop target all the way to 30 m.
4. Solar Array Recharge Time Breakdown
The Sungrow SH10RS Hybrid Inverter + Battery accepts up to 15,000 W of photovoltaic input. Real arrays rarely deliver nameplate output, so we apply an 80% harvest factor for MPPT conversion, cell temperature and soiling, and convert hours to days using 4.5 peak-sun-hours — a conservative annual average for the US, southern Europe and Australia (UK winters can fall below 1.5).
| PV array | Real harvest | 0–100% recharge | Sun-days @ 4.5 PSH | Net with load @ 50% |
|---|---|---|---|---|
| 1,600 W | 1,280 W | 7.5 hrs | 1.7 | +1,105 W |
| 3,000 W | 2,400 W | 4.0 hrs | 0.9 | +2,225 W |
| 6,000 W | 4,800 W | 2.0 hrs | 0.4 | +4,625 W |
| 12,000 W | 9,600 W | 1.0 hrs | 0.2 | +9,425 W |
| 15,000 W | 12,000 W | 48 min | 0.2 | +11,825 W |
A typical 800 W portable array refills the battery in about 15.0 hrs of strong sun, while maxing out the 15,000 W input cuts that to 48 min. To fully offset the 5 LPM Home Stationary Oxygen Concentrator at a 50% duty cycle (175 W average) during daylight you need roughly 250 W of panels, which this unit can accept.
5. Frequently Asked Questions
Can the Sungrow SH10RS Hybrid Inverter + Battery run a 5 LPM Home Stationary Oxygen Concentrator?
Yes. The Sungrow SH10RS Hybrid Inverter + Battery delivers 10,000 W continuous and 15,000 W surge, covering the 5 LPM Home Stationary Oxygen Concentrator's 350 W running and 600 W start-up draw at 4% inverter utilization.
How long will the Sungrow SH10RS Hybrid Inverter + Battery run a 5 LPM Home Stationary Oxygen Concentrator?
With 9,600 Wh of capacity and 85% inverter efficiency, expect about 23.3 hrs of continuous operation and 46.6 hrs at a 50% duty cycle. Adding solar input during the day extends this further.
What breaker and wire size do I need to connect a 5 LPM Home Stationary Oxygen Concentrator to the Sungrow SH10RS Hybrid Inverter + Battery?
At 230 V the load draws 1.5 A. Under BS 7671 / IEC 60364 the protective device must be at least the design current (Ib ≤ In ≤ Iz), so use a 6 A MCB with RCD protection on 1.5 mm² copper cable for runs up to 7.5 m (0.1% voltage drop). Connection: BS 1363 13A / Schuko CEE 7/4 / AS/NZS 3112 10A.
How long does it take to recharge the Sungrow SH10RS Hybrid Inverter + Battery with solar panels?
With an 800 W array and an 80% real-world harvest factor, a full recharge takes about 15.0 hrs of peak sun (3.3 days at 4.5 peak-sun-hours). At its maximum 15,000 W solar input it drops to 48 min.
Methodology & safety note
Specifications come from manufacturer datasheets in our open dataset; ampacity and resistance values follow NEC Table 310.16 and Chapter 9 Table 8, and BS 7671 Appendix 4. Calculations assume copper conductors, 30 °C ambient and no bundling derating. Inverter-to-panel connections require a listed transfer switch or interlock to prevent back-feeding the grid. These results are an engineering estimate, not a substitute for a licensed electrician and local permit. See our methodology and safety disclaimer.