Engineering report · reviewed against NEC 2026 & BS 7671:2018+A2
Engineering Breakdown: Running a 4-Ton Central AC (With Micro-Air EasyStart) on the Victron MultiPlus-II 48/5000 + 10kWh LiFePO4 Bank
When pairing the Victron MultiPlus-II 48/5000 + 10kWh LiFePO4 Bank (10,240 Wh LiFePO4 capacity, 4,000 W continuous, 9,000 W surge) with a 4-Ton Central AC (With Micro-Air EasyStart) (3,800 W running, 6,800 W starting surge), the system operates at 95% of continuous inverter capacity on a 240 V North American circuit and 95% on a 230 V UK/EU/AU circuit. Our North American verdict is 240V Split-Phase Required, so the runtime figures below are theoretical battery-energy values only. Wiring the connection over a 25 ft run calls for a 20 A breaker and 12 AWG copper, terminated at a Hardwired 240V / 14-50 Transfer Switch connection.
1. Compatibility Verdict & Inverter Load Utilization
In North American mode the 4-Ton Central AC (With Micro-Air EasyStart) loads the Victron MultiPlus-II 48/5000 + 10kWh LiFePO4 Bank's inverter to 95% of its 4,000 W continuous rating and 76% of its 9,000 W surge rating. The blocking issue is voltage, not just wattage: the load requires a 240 V split-phase supply while this unit outputs 120 V only. The leanest compatible alternative in our database is the Oukitel BP5000 Pro Max.
| Check | Load requires | Victron MultiPlus-II 48/5000 + 10kWh LiFePO4 Bank provides | US/NA | UK/EU/AU |
|---|---|---|---|---|
| Continuous output | 3,800 W | 4,000 W | Pass | Pass |
| Start-up surge | 6,800 W | 9,000 W | Pass | Pass |
| Voltage | 240 V / 230 V | 120 V / 230 V | Fail | Pass |
| Connection | Hardwired 240V / 14-50 Transfer Switch | Hardwired AC Distribution / L5-30R | UK/EU/AU: Hardwired via DP isolator · IEC 60309 32A | |
Compressor-driven HVAC equipment is the hardest category for any inverter because of locked-rotor amperage (LRA): for a fraction of a second the motor pulls 1.8× its running power (6,800 W here). The Victron MultiPlus-II 48/5000 + 10kWh LiFePO4 Bank is rated for 9,000 W of surge, which covers that inrush. Thermostat cycling means the compressor rarely runs 100% of the time; mild weather typically produces 30–50% duty cycles, while peak summer afternoons push toward 80–100%. Fitting a soft-start module (Micro-Air EasyStart, SoftStartRV or a variable-speed inverter compressor) is the single cheapest way to make a marginal pairing reliable.
The Victron MultiPlus-II 48/5000 + 10kWh LiFePO4 Bank is a marine and RV inverter-charger. Its strength is power quality and PowerAssist blending with shore or generator input rather than standalone 240V output.
Compatible alternative: the Oukitel BP5000 Pro Max with the 4-Ton Central AC (With Micro-Air EasyStart) report shows the full sizing for a unit that passes all three checks.
2. Real-World Runtime by Duty Cycle
Nameplate capacity is not usable capacity. DC-to-AC conversion, battery management overhead and cell protection reduce the 10,240 Wh rating to about 8,704 Wh of deliverable AC energy (85% system efficiency). Duty cycle is the share of each hour the load actually draws its running power — thermostats, pressure switches and intermittent use all lower it.
| Duty cycle | Average draw | Runtime (no solar) | Energy per 24 h |
|---|---|---|---|
| 25% | 950 W | 9.2 hrs | 22.8 kWh |
| 50% | 1,900 W | 4.6 hrs | 45.6 kWh |
| 65% | 2,470 W | 3.5 hrs | 59.3 kWh |
| 100% | 3,800 W | 2.3 hrs | 91.2 kWh |
Even at a 50% duty cycle the battery lasts 4.6 hrs, so plan on solar, grid or generator recharging for anything longer than an evening outage. Because the inverter cannot actually run this load in North American mode, treat these numbers as an energy-budget reference for a compatible inverter of the same capacity.
3. NEC 125% Breaker & Copper Wire Gauge Sizing
NEC 210.19(A) and 210.20(A) require conductors and overcurrent devices for continuous loads — anything running three hours or more, which includes EV charging and HVAC — to be rated at 125% of the load current. For this pairing: 3,800 W ÷ 240 V = 15.8 A, × 1.25 = 19.8 A, which rounds up to the next standard NEC 240.6 size of 20 A. The conductor must be protected by that breaker (75 °C ampacity at least 20 A) and keep round-trip voltage drop at or below 3%, so longer runs are upsized.
Voltage drop % = (2 × L × I × R) ÷ V × 100
North America (NEC, THHN copper, 75 °C)
| One-way distance | Breaker | Min. copper | Voltage drop | Note |
|---|---|---|---|---|
| 25 ft (7.6 m) | 20 A | 12 AWG | 0.64% | Sized by ampacity |
| 50 ft (15.2 m) | 20 A | 12 AWG | 1.27% | Sized by ampacity |
| 75 ft (22.9 m) | 20 A | 12 AWG | 1.91% | Sized by ampacity |
| 100 ft (30.5 m) | 20 A | 12 AWG | 2.55% | Sized by ampacity |
UK / EU / Australia (IEC 60364 / BS 7671, PVC copper, method C)
IEC-based codes size protection by design current rather than a blanket 125% multiplier: Ib ≤ In ≤ Iz. At 230 V the load draws 16.5 A, so a 20 A Type B/C MCB with RCD protection applies. In the UK, BS 7671 Section 722 additionally requires a dedicated circuit and Type A or Type B RCD for EV charge points.
| One-way distance | MCB | Min. cable | Voltage drop |
|---|---|---|---|
| 7.5 m (25 ft) | 20 A | 2.5 mm² | 0.80% |
| 15 m (49 ft) | 20 A | 2.5 mm² | 1.60% |
| 22.5 m (74 ft) | 20 A | 2.5 mm² | 2.40% |
| 30 m (98 ft) | 20 A | 4.0 mm² | 1.99% |
Because the current is modest, 12 AWG copper stays within the voltage-drop target all the way to 100 ft.
4. Solar Array Recharge Time Breakdown
The Victron MultiPlus-II 48/5000 + 10kWh LiFePO4 Bank accepts up to 5,000 W of photovoltaic input. Real arrays rarely deliver nameplate output, so we apply an 80% harvest factor for MPPT conversion, cell temperature and soiling, and convert hours to days using 4.5 peak-sun-hours — a conservative annual average for the US, southern Europe and Australia (UK winters can fall below 1.5).
| PV array | Real harvest | 0–100% recharge | Sun-days @ 4.5 PSH | Net with load @ 50% |
|---|---|---|---|---|
| 400 W | 320 W | 32.0 hrs | 7.1 | −1,580 W |
| 800 W | 640 W | 16.0 hrs | 3.6 | −1,260 W |
| 1,600 W | 1,280 W | 8.0 hrs | 1.8 | −620 W |
| 3,000 W | 2,400 W | 4.3 hrs | 0.9 | +500 W |
| 5,000 W | 4,000 W | 2.6 hrs | 0.6 | +2,100 W |
A typical 800 W portable array refills the battery in about 16.0 hrs of strong sun, while maxing out the 5,000 W input cuts that to 2.6 hrs. To fully offset the 4-Ton Central AC (With Micro-Air EasyStart) at a 50% duty cycle (1,900 W average) during daylight you need roughly 2,400 W of panels, which this unit can accept.
5. Frequently Asked Questions
Can the Victron MultiPlus-II 48/5000 + 10kWh LiFePO4 Bank run a 4-Ton Central AC (With Micro-Air EasyStart)?
Not reliably in North America — our verdict is "240V Split-Phase Required". The load needs 240 V split-phase power and the Victron MultiPlus-II 48/5000 + 10kWh LiFePO4 Bank outputs 120 V only. The Oukitel BP5000 Pro Max is a compatible alternative. In UK/EU/AU 230 V mode the verdict is "Compatible · High Load".
How long will the Victron MultiPlus-II 48/5000 + 10kWh LiFePO4 Bank run a 4-Ton Central AC (With Micro-Air EasyStart)?
With 10,240 Wh of capacity and 85% inverter efficiency, expect about 2.3 hrs of continuous operation and 4.6 hrs at a 50% duty cycle — theoretical figures, since the inverter cannot actually sustain this load. Adding solar input during the day extends this further.
What breaker and wire size do I need to connect a 4-Ton Central AC (With Micro-Air EasyStart) to the Victron MultiPlus-II 48/5000 + 10kWh LiFePO4 Bank?
In the US, 3,800 W at 240 V is 15.8 A; applying the NEC 125% continuous-load rule gives 19.8 A, so use a 20 A breaker and 12 AWG copper for runs up to 25 ft (0.6% voltage drop). In 230 V markets the load draws 16.5 A, protected by a 20 A MCB on 2.5 mm² cable for runs up to 7.5 m. Receptacle: Hardwired 240V / 14-50 Transfer Switch (US) or Hardwired via DP isolator · IEC 60309 32A (UK/EU/AU).
How long does it take to recharge the Victron MultiPlus-II 48/5000 + 10kWh LiFePO4 Bank with solar panels?
With an 800 W array and an 80% real-world harvest factor, a full recharge takes about 16.0 hrs of peak sun (3.6 days at 4.5 peak-sun-hours). At its maximum 5,000 W solar input it drops to 2.6 hrs.
Methodology & safety note
Specifications come from manufacturer datasheets in our open dataset; ampacity and resistance values follow NEC Table 310.16 and Chapter 9 Table 8, and BS 7671 Appendix 4. Calculations assume copper conductors, 30 °C ambient and no bundling derating. Inverter-to-panel connections require a listed transfer switch or interlock to prevent back-feeding the grid. These results are an engineering estimate, not a substitute for a licensed electrician and local permit. See our methodology and safety disclaimer.