Engineering report · reviewed against NEC 2026 & BS 7671:2018+A2
Engineering Breakdown: Running a 1.5 HP Deep Well Submersible Pump (240V) on the Victron MultiPlus-II 48/5000 + 10kWh LiFePO4 Bank
When pairing the Victron MultiPlus-II 48/5000 + 10kWh LiFePO4 Bank (10,240 Wh LiFePO4 capacity, 4,000 W continuous, 9,000 W surge) with a 1.5 HP Deep Well Submersible Pump (240V) (2,200 W running, 6,200 W starting surge), the system operates at 55% of continuous inverter capacity on a 240 V North American circuit and 55% on a 230 V UK/EU/AU circuit. Our North American verdict is 240V Split-Phase Required, so the runtime figures below are theoretical battery-energy values only. Wiring the connection over a 25 ft run calls for a 15 A breaker and 14 AWG copper, terminated at a NEMA L14-30P / 14-50P connection.
1. Compatibility Verdict & Inverter Load Utilization
In North American mode the 1.5 HP Deep Well Submersible Pump (240V) loads the Victron MultiPlus-II 48/5000 + 10kWh LiFePO4 Bank's inverter to 55% of its 4,000 W continuous rating and 69% of its 9,000 W surge rating. The blocking issue is voltage, not just wattage: the load requires a 240 V split-phase supply while this unit outputs 120 V only. The leanest compatible alternative in our database is the Zendure SuperBase V6400.
| Check | Load requires | Victron MultiPlus-II 48/5000 + 10kWh LiFePO4 Bank provides | US/NA | UK/EU/AU |
|---|---|---|---|---|
| Continuous output | 2,200 W | 4,000 W | Pass | Pass |
| Start-up surge | 6,200 W | 9,000 W | Pass | Pass |
| Voltage | 240 V / 230 V | 120 V / 230 V | Fail | Pass |
| Connection | NEMA L14-30P / 14-50P | Hardwired AC Distribution / L5-30R | UK/EU/AU: BS 1363 13A / Schuko CEE 7/4 / AS/NZS 3112 10A | |
Pumps are short-cycling, high-inrush loads. A well or sump pump might run for only 1–3 minutes at a time, but every start pulls 6,200 W — 2.8× its 2,200 W running draw — as the motor accelerates a column of water. That is why a pump that "only uses 2,200 W" still trips undersized inverters. Deep-well submersibles in North America are almost always 240 V two-wire or three-wire motors, so a 120 V-only station cannot drive them without a step-up transformer. A larger pressure tank reduces the number of starts per hour and is a worthwhile upgrade for off-grid systems built around the Victron MultiPlus-II 48/5000 + 10kWh LiFePO4 Bank.
The Victron MultiPlus-II 48/5000 + 10kWh LiFePO4 Bank is a marine and RV inverter-charger. Its strength is power quality and PowerAssist blending with shore or generator input rather than standalone 240V output.
Compatible alternative: the Zendure SuperBase V6400 with the 1.5 HP Deep Well Submersible Pump (240V) report shows the full sizing for a unit that passes all three checks.
2. Real-World Runtime by Duty Cycle
Nameplate capacity is not usable capacity. DC-to-AC conversion, battery management overhead and cell protection reduce the 10,240 Wh rating to about 8,704 Wh of deliverable AC energy (85% system efficiency). Duty cycle is the share of each hour the load actually draws its running power — thermostats, pressure switches and intermittent use all lower it.
| Duty cycle | Average draw | Runtime (no solar) | Energy per 24 h |
|---|---|---|---|
| 25% | 550 W | 15.8 hrs | 13.2 kWh |
| 50% | 1,100 W | 7.9 hrs | 26.4 kWh |
| 65% | 1,430 W | 6.1 hrs | 34.3 kWh |
| 100% | 2,200 W | 4.0 hrs | 52.8 kWh |
Even at a 50% duty cycle the battery lasts 7.9 hrs, so plan on solar, grid or generator recharging for anything longer than an evening outage. Because the inverter cannot actually run this load in North American mode, treat these numbers as an energy-budget reference for a compatible inverter of the same capacity.
3. NEC 125% Breaker & Copper Wire Gauge Sizing
NEC 210.19(A) and 210.20(A) require conductors and overcurrent devices for continuous loads — anything running three hours or more, which includes EV charging and HVAC — to be rated at 125% of the load current. For this pairing: 2,200 W ÷ 240 V = 9.2 A, × 1.25 = 11.5 A, which rounds up to the next standard NEC 240.6 size of 15 A. The conductor must be protected by that breaker (75 °C ampacity at least 15 A) and keep round-trip voltage drop at or below 3%, so longer runs are upsized.
Voltage drop % = (2 × L × I × R) ÷ V × 100
North America (NEC, THHN copper, 75 °C)
| One-way distance | Breaker | Min. copper | Voltage drop | Note |
|---|---|---|---|---|
| 25 ft (7.6 m) | 15 A | 14 AWG | 0.59% | Sized by ampacity |
| 50 ft (15.2 m) | 15 A | 14 AWG | 1.17% | Sized by ampacity |
| 75 ft (22.9 m) | 15 A | 14 AWG | 1.76% | Sized by ampacity |
| 100 ft (30.5 m) | 15 A | 14 AWG | 2.35% | Sized by ampacity |
UK / EU / Australia (IEC 60364 / BS 7671, PVC copper, method C)
IEC-based codes size protection by design current rather than a blanket 125% multiplier: Ib ≤ In ≤ Iz. At 230 V the load draws 9.6 A, so a 10 A Type B/C MCB with RCD protection applies. In the UK, BS 7671 Section 722 additionally requires a dedicated circuit and Type A or Type B RCD for EV charge points.
| One-way distance | MCB | Min. cable | Voltage drop |
|---|---|---|---|
| 7.5 m (25 ft) | 10 A | 1.5 mm² | 0.75% |
| 15 m (49 ft) | 10 A | 1.5 mm² | 1.51% |
| 22.5 m (74 ft) | 10 A | 1.5 mm² | 2.26% |
| 30 m (98 ft) | 10 A | 2.5 mm² | 1.85% |
Because the current is modest, 14 AWG copper stays within the voltage-drop target all the way to 100 ft.
4. Solar Array Recharge Time Breakdown
The Victron MultiPlus-II 48/5000 + 10kWh LiFePO4 Bank accepts up to 5,000 W of photovoltaic input. Real arrays rarely deliver nameplate output, so we apply an 80% harvest factor for MPPT conversion, cell temperature and soiling, and convert hours to days using 4.5 peak-sun-hours — a conservative annual average for the US, southern Europe and Australia (UK winters can fall below 1.5).
| PV array | Real harvest | 0–100% recharge | Sun-days @ 4.5 PSH | Net with load @ 50% |
|---|---|---|---|---|
| 400 W | 320 W | 32.0 hrs | 7.1 | −780 W |
| 800 W | 640 W | 16.0 hrs | 3.6 | −460 W |
| 1,600 W | 1,280 W | 8.0 hrs | 1.8 | +180 W |
| 3,000 W | 2,400 W | 4.3 hrs | 0.9 | +1,300 W |
| 5,000 W | 4,000 W | 2.6 hrs | 0.6 | +2,900 W |
A typical 800 W portable array refills the battery in about 16.0 hrs of strong sun, while maxing out the 5,000 W input cuts that to 2.6 hrs. To fully offset the 1.5 HP Deep Well Submersible Pump (240V) at a 50% duty cycle (1,100 W average) during daylight you need roughly 1,400 W of panels, which this unit can accept.
5. Frequently Asked Questions
Can the Victron MultiPlus-II 48/5000 + 10kWh LiFePO4 Bank run a 1.5 HP Deep Well Submersible Pump (240V)?
Not reliably in North America — our verdict is "240V Split-Phase Required". The load needs 240 V split-phase power and the Victron MultiPlus-II 48/5000 + 10kWh LiFePO4 Bank outputs 120 V only. The Zendure SuperBase V6400 is a compatible alternative. In UK/EU/AU 230 V mode the verdict is "Verified Compatible".
How long will the Victron MultiPlus-II 48/5000 + 10kWh LiFePO4 Bank run a 1.5 HP Deep Well Submersible Pump (240V)?
With 10,240 Wh of capacity and 85% inverter efficiency, expect about 4.0 hrs of continuous operation and 7.9 hrs at a 50% duty cycle — theoretical figures, since the inverter cannot actually sustain this load. Adding solar input during the day extends this further.
What breaker and wire size do I need to connect a 1.5 HP Deep Well Submersible Pump (240V) to the Victron MultiPlus-II 48/5000 + 10kWh LiFePO4 Bank?
In the US, 2,200 W at 240 V is 9.2 A; applying the NEC 125% continuous-load rule gives 11.5 A, so use a 15 A breaker and 14 AWG copper for runs up to 25 ft (0.6% voltage drop). In 230 V markets the load draws 9.6 A, protected by a 10 A MCB on 1.5 mm² cable for runs up to 7.5 m. Receptacle: NEMA L14-30P / 14-50P (US) or BS 1363 13A / Schuko CEE 7/4 / AS/NZS 3112 10A (UK/EU/AU).
How long does it take to recharge the Victron MultiPlus-II 48/5000 + 10kWh LiFePO4 Bank with solar panels?
With an 800 W array and an 80% real-world harvest factor, a full recharge takes about 16.0 hrs of peak sun (3.6 days at 4.5 peak-sun-hours). At its maximum 5,000 W solar input it drops to 2.6 hrs.
Methodology & safety note
Specifications come from manufacturer datasheets in our open dataset; ampacity and resistance values follow NEC Table 310.16 and Chapter 9 Table 8, and BS 7671 Appendix 4. Calculations assume copper conductors, 30 °C ambient and no bundling derating. Inverter-to-panel connections require a listed transfer switch or interlock to prevent back-feeding the grid. These results are an engineering estimate, not a substitute for a licensed electrician and local permit. See our methodology and safety disclaimer.